NOTE: Make sure that the tensioner rod has been fully turned clockwise. The valve clearance must be measured again and the above steps should be repeated if the measurement is still incorrect. Engine oil level check 1. Insert the tube of an oil changer into the oil filler hole. Operate the oil changer to extract the oil. If the oil filter is also to be replaced, per- form the following procedure. Remove the air filter element and check it for dirt and oil. Replace the air filter ele- ment if there is any oil buildup.
Also, it is suggested to apply a thin film of anti- seize compound to the spark plug threads to prevent thread seizure. Electro- lyte contains sulfuric acid. Avoid contact with skin, eyes or clothing. Antidotes External: Flush with water.
Internal: Drink large quantities of water or milk. Maximum impeller-to-housing clearance: 0. Fuel pump module removal 1. Fuel tank inspection 1. Fuel pump filter inspection 1. Hose clamps installation 1.
Page Fuel Injectors Inspection Fuel injector resistance: reference data NOTE: Insufficient compression pressure will result in a loss of performance. Minimum compression pressure reference data : 1, kPa With the throttle wide open, crank the engine until the reading on the compres- sion gauge stabilizes.
NOTE: Measure the clearances with a straightedge and thickness gauge. Clearance a: 0—0. Oil strainer inspection 1. Oil tank installation 1. Oil breather plate bolt: 1st: 1. Oil pump installation 1.
Maximum camshaft runout: 0. Camshaft-journal-to-camshaft- cap clearance: 0. Camshaft journal diameter: Intake: NOTE: Gradually tighten the intake and exhaust camshaft cap bolts in 2—3 steps in the sequence shown. Cylinder head inspection 1. Cylinder head warpage limit: 0. Intake valve lifter Intake valve pad Intake valve cotter Intake valve upper spring seat Valve spring free length: Intake valve spring: Valve stem diameter a: Intake valve: 3.
Install the new valve guide 2 by striking the special service tool from the camshaft side until the valve guide clip 3 contacts the cylinder head. NOTE: Apply engine oil to the surface of the new valve guide. In modern society, there is a special category of people who simply do not represent their lives without a certain dose of adrenaline. They love to jump with a parachute, to conquer the mountain slopes or, for example, ride a jet ski. It is about watercraft and will be discussed.
These "cars" are rapidly gaining popularity among all speed lovers. On them you get not only a charge of adrenaline, but also enjoy the sea spaces. Yamaha watercraft , which for more than 50 years is the world leader in the production of motorcycle equipment, are in great demand among lovers of water adventures. The company has in its assortment all the latest models that will allow to get maximum pleasure from riding a jet ski.
When test running an engine indoors e. Protect your hands and feet by wearing protective gloves or safety shoes when necessary. Under normal conditions, the lubricants mentioned in this manual should not harm or be hazardous to your skin. However, you should follow these precautions to minimize any risk when working with lubricants. Maintain good standards of personal and industrial hygiene.
Change and wash clothing as soon as possible if soiled with lubricants. Avoid contact with skin. Do not, for example, place a soiled rag in your pocket. Wash hands and any other part of the body thoroughly with soap and hot water after contact with a lubricant or lubricant soiled clothing has been made. To protect your skin, apply a protective cream to your hands before working on the watercraft. Keep a supply of clean, lint-free cloths for wiping up spills, etc. The right tools Use the recommended special service tools to protect parts from damage.
Tightening torques Follow the tightening torque specifications provided throughout the manual. When tightening nuts, bolts, and screws, tighten the large sizes first, and tighten fasteners starting in the center and moving outward. Non-reusable parts Always use new gaskets, seals, O-rings, oil seals, cotter pins, circlips, etc. Use compressed air to remove dust and dirt during disassembly. Apply engine oil to the contact surfaces of moving parts during assembly.
Install bearings with the manufacture identification mark in the direction indication in the installation procedure. In addition, be sure to lubricate the bearings liberally. Apply a thin coat of water-resistant grease to the lip and periphery of an oil seal before installation. Check that moving parts operate normally after assembly. Improvisations and using improper tools can damage the equipment. YB Fuel and oil Fuel type Minimum fuel rating Fuel tank capacity Engine oil type Engine oil grade Engine oil quantity without oil filter replacement with oil filter replacement.
Regular unleaded gasoline 86 90 60 The figures are for reference only. Air filter case Air filter case bracket Air intake hose clamp Throttle cable Accelerator position sensor Throttle body assembly. Lower handlebar cover Throttle lever assembly Handlebar switch assembly Grip end Steering column Steering cable ball joint Steering arm Steering sensor Spacer Shift cable holder Deluxe model only Shift cable seal Deluxe model only.
This chart specifies tightening torques for standard fasteners with a standard ISO thread pitch.
0コメント